Supermicro SYS-7045A-TB Manual do Utilizador Página 1

® SUPERWORKSTATION 7045A-T SUPERWORKSTATION 7045A-8 USER’S MANUAL1.0a SUPER

NotesxSUPERWORKSTATION 7045A-T/7045A-8 User's Manual

A-4SUPERWORKSTATION 7045A-T/7045A-8 User's ManualInvalid System Confi guration DataProblem with NVRAM (CMOS) data.I/O device IRQ confl ictI/O devic

A-5Appendix A: BIOS POST MessagesPress <F1> to resume, <F2> to Setup, <F3> for previous Displayed after any recoverable error messag

A-6SUPERWORKSTATION 7045A-T/7045A-8 User's ManualNotes

Appendix B: BIOS POST CodesB-1This section lists the POST (Power On Self Test) codes for the PhoenixBIOS. POST codes are divided into two categories:

B-2SUPERWORKSTATION 7045A-T/7045A-8 User's ManualPOST Code Description18h 8254 timer initialization1Ah 8237 DMA controller initializati

Appendix B: BIOS POST CodesB-3POST Code Description5Ch Test RAM between 512 and 640 kB60h Test extended memory62h Test extended memory a

B-4SUPERWORKSTATION 7045A-T/7045A-8 User's ManualPOST Code Description99h Check for SMART Drive (optional)9Ah Shadow option ROMs9Ch

Appendix B: BIOS POST CodesB-5POST Code DescriptionCDh Re-map I/O and memory for PCMCIACEh Initialize digitizer and display messageD2h U

B-6SUPERWORKSTATION 7045A-T/7045A-8 User's ManualNotes

Appendix C: Software InstallationC-1 Appendix C Software Installation After all the hardware has been installed, you must fi rst confi gure Intel&apo

Chapter 1 Introduction1-1 OverviewSupermicro's SuperWorkstation 7045A-T/7045A-8 is a high-end dual processor workstation

C-2SUPERWORKSTATION 7045A-T/7045A-8 User's ManualRAID Confi gurationsThe following types of RAID confi gurations are supported:RAID 0 (Data Stripin

Appendix C: Software InstallationC-3Using the Intel ESB2 SATA RAID Utility Program1. Creating, Deleting and Resetting RAID Volumes: a. After the syste

C-4SUPERWORKSTATION 7045A-T/7045A-8 User's Manual2. Specify a name for the RAID 0 set and press the <Tab> key or the <Enter> key to g

Appendix C: Software InstallationC-5Creating a RAID 1 Volume1. Select "Create RAID Volume" from the main menu and press the <Enter> ke

C-6SUPERWORKSTATION 7045A-T/7045A-8 User's ManualCreating a RAID 10 (RAID 1+ RAID 0)1. Select "Create RAID Volume" from the main menu a

Appendix C: Software InstallationC-7Creating a RAID 5 Set (Parity)1. Select "Create RAID Volume" from the main menu and press the <Enter&

C-8SUPERWORKSTATION 7045A-T/7045A-8 User's ManualDeleting a RAID VolumeWarning: Be sure to back up your data before deleting a RAID set. You wil

Appendix C: Software InstallationC-9Resetting to Non-RAID and Resetting a RAID HDD 1. From the main menu, select item3-Reset Disks to Non- RAID, and

C-10SUPERWORKSTATION 7045A-T/7045A-8 User's ManualC-2 Installing Windows XP/2000/2003 on RAID SystemsNew Operating System: Windows XP/2000/2003

Appendix C: Software InstallationC-11C-3 Installing the Operating System and other SoftwareAfter all the hardware has been installed, you must fi rst

1-2SUPERWORKSTATION 7045A-T/7045A-8 User's Manual1-2 Serverboard FeaturesAt the heart of the 7045A-T/7045A-8 lies the X7DAE/X7DA8, a dual process

C-12SUPERWORKSTATION 7045A-T/7045A-8 User's ManualSupero Doctor IIIThe Supero Doctor III program is a Web base management tool that supports remo

Appendix C: Software InstallationC-13Note: SD III Software Revision 1.0 can be downloaded from our Web Site at: ftp://ftp.supermicro.com/utility/Super

C-14SUPERWORKSTATION 7045A-T/7045A-8 User's ManualNotes

D-1Appendix D: System Specifi cationsAppendix DSystem Specifi cationsProcessors Single or dual 604-pin Intel® XeonTM processors at a front side (s

D-2SUPERWORKSTATION 7045A-T/7045A-8 User's ManualServerboard Model: X7DAE/X7DA8 Form Factor: Extended ATX Dimensions: 12 x 13.05

D-3Appendix D: System Specifi cationsRegulatory Compliance Electromagnetic Emissions: FCC Class B, EN 55022 Class B, EN 61000-3-2/-3-3, CISPR

D-4SUPERWORKSTATION 7045A-T/7045A-8 User's ManualNotes

1-3Chapter 1: IntroductionPCI Expansion SlotsThe X7DAE/X7DA8 has seven PCI expansion slots, which includes two x16 PCI-Express slots (supports SLI), o

1-4SUPERWORKSTATION 7045A-T/7045A-8 User's ManualSCSI Subsystem (7045A-8)The SCSI subsystem supports up to eight 80-pin SCA Ultra320 SCSI hard dr

1-5Chapter 1: IntroductionFigure 1-1. Intel 5000X Chipset: System Block Diagram Note: This is a general block diagram. Please see Chapter 5 for deta

1-6SUPERWORKSTATION 7045A-T/7045A-8 User's Manual1-4 Contacting SupermicroHeadquarters Address: SuperMicro Computer, Inc.

Chapter 2: Server Installation2-1 Chapter 2 Server Installation 2-1 OverviewThis chapter provides a

2-2SUPERWORKSTATION 7045A-T/7045A-8 User's ManualChoosing a Setup Location - Leave enough clearance in front of the system to enable you to

Chapter 2: Server Installation2-3Rack Mounting ConsiderationsAmbient Operating TemperatureIf installed in a closed or multi-unit rack assembly, the am

Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not copy any part of this document.Information in this document i

2-4SUPERWORKSTATION 7045A-T/7045A-8 User's Manual2-4 Installing the System into a RackThis section provides information on installing the system

Chapter 2: Server Installation2-5Installing the Chassis RailsYou will need to remove the top bezel cover and the feet to add rack rails to the chassis

2-6SUPERWORKSTATION 7045A-T/7045A-8 User's ManualInstalling the Rack RailsDetermine where you want to place the SuperWorkstation 7045A-T/7045A-8

Chapter 2: Server Installation2-7Figure 2-4. Installing the Server into a RackInstalling the Server into the RackYou should now have rails attached

2-8SUPERWORKSTATION 7045A-T/7045A-8 User's Manual2-5 Checking the Serverboard SetupAfter setting up the the system, you will need to open the un

Chapter 2: Server Installation2-92-6 Checking the Drive Bay SetupNext, you should check to make sure the peripheral drives and the SCSI drives and SC

2-10SUPERWORKSTATION 7045A-T/7045A-8 User's ManualFigure 2-5. Accessing the Inside of the System (Rack Confi guration shown)

Chapter 3: System Interface3-1 Chapter 3 System Interface3-1 OverviewThere are several LEDs on the control panel as well

3-2SUPERWORKSTATION 7045A-T/7045A-8 User's Manual3-3 Control Panel LEDsThe control panel located on the front of the SC743TQ-645/SC743S1-645 chas

Chapter 3: System Interface3-3 Power Fail: Indicates a power supply module has failed. This LED is inended for use with systems that have redundan

iiiPrefacePrefaceAbout This ManualThis manual is written for professional system integrators and PC technicians. It provides information for the inst

3-4SUPERWORKSTATION 7045A-T/7045A-8 User's ManualNotes

Chapter 4: System Safety4-1 Chapter 4 System Safety4-1 Electrical Safety Precautions!Basic electrical safety precautions should be

4-2SUPERWORKSTATION 7045A-T/7045A-8 User's Manual4-2 General Safety PrecautionsFollow these rules to ensure general safety:  Keep the area aro

Chapter 4: System Safety4-34-3 ESD Precautions Electrostatic discharge (ESD) is generated by two objects with different electrical charges com

4-4SUPERWORKSTATION 7045A-T/7045A-8 User's Manual4-4 Operating Precautions Care must be taken to assure that all chassis covers are in pl

Chapter 5: Advanced Serverboard Setup5-1 Chapter 5 Advanced Serverboard SetupThis chapter covers the steps required to install pro

5-2SUPERWORKSTATION 7045A-T/7045A-8 User's ManualIMPORTANT! Always connect the power cord last and remove it fi rst before add-ing, removing or ch

Chapter 5: Advanced Serverboard Setup5-3Socket keyCPU installed in socketPnP cap released from load plate3. Use your thumb and your index fi nger to ho

5-4SUPERWORKSTATION 7045A-T/7045A-8 User's ManualWarning! We do not recommend that the CPU or the heatsink be removed. However, if you do need

Chapter 5: Advanced Serverboard Setup5-55-3 Connecting CablesNow that the processors are installed, the next step is to connect the cables to the ser

SUPERWORKSTATION 7045A-T/7045A-8 User's ManualivChapter 4: System SafetyYou should thoroughly familiarize yourself with this chapter for a gener

5-6SUPERWORKSTATION 7045A-T/7045A-8 User's ManualFigure 5-3. Front Control Panel Header Pins (JF1)Connecting the Control PanelJF1 contains header

Chapter 5: Advanced Serverboard Setup5-75-4 I/O PortsThe I/O ports are color coded in conformance with the PC 99 specifi cation. See Figure 5-4 below

5-8SUPERWORKSTATION 7045A-T/7045A-8 User's Manual5-5 Installing Memory Note: Check the Supermicro web site for recommended memory modules.CA

Chapter 5: Advanced Serverboard Setup5-9Figure 5-5. Installing DIMM into SlotTo Install: Insert module vertically and press down until it snaps into p

5-10SUPERWORKSTATION 7045A-T/7045A-8 User's ManualFigure 5-6. SUPER X7DA8/X7DAE Layout*(not drawn to scale)5-7 Serverboard DetailsSUPER X7DA8

Chapter 5: Advanced Serverboard Setup5-11X7DAE/X7DA8 Quick ReferenceJumper Description Default Setting J3P 3rd Power Fail Detect Open (Dis

5-12SUPERWORKSTATION 7045A-T/7045A-8 User's Manual5-8 Connector Defi nitions Power LED The Power LED connection is located on pins 15 and 16 of JF

Chapter 5: Advanced Serverboard Setup5-13Overheat/Fan Fail LED (OH)Connect an LED to the OH connection on pins 7 and 8 of JF1 to provide ad-vanced war

5-14SUPERWORKSTATION 7045A-T/7045A-8 User's ManualReset Button The Reset Button connection is lo-cated on pins 3 and 4 of JF1. Attach it to the

Chapter 5: Advanced Serverboard Setup5-15Chassis Intrusion A Chassis Intrusion header is located at JL1. Attach the appropriate cable to inform you o

vPrefaceNotes

5-16SUPERWORKSTATION 7045A-T/7045A-8 User's ManualATX PS/2 Keyboard and PS/2 Mouse PortsThe ATX PS/2 keyboard and the PS/2 mouse ports are locate

Chapter 5: Advanced Serverboard Setup5-17Wake-On-LANThe Wake-On-LAN header is desig-nated JWOL. See the table on the right for pin defi nitions. You

5-18SUPERWORKSTATION 7045A-T/7045A-8 User's ManualAC'97 Audio AC'97 provides high quality onboard audio. The X7DAE/X7DA8 features 6-ch

Chapter 5: Advanced Serverboard Setup5-195-9 Jumper SettingsExplanation of JumpersTo modify the operation of the serverboard, jumpers can be used

5-20SUPERWORKSTATION 7045A-T/7045A-8 User's ManualJLAN Enable/Disable Change the setting of jumper JPL1 and JPL2 to enable or disable the on-boar

Chapter 5: Advanced Serverboard Setup5-21SCSI Controller Enable/Disable (X7DA8 only)Jumper JPA1 is used to enable or dis-able the onboard SCSI control

5-22SUPERWORKSTATION 7045A-T/7045A-8 User's ManualAudio Enable/Dis-able Jumper Setttings (JPAC)Pin# Defi nition 1-2 Enabled2-3 DisabledAud

Chapter 5: Advanced Serverboard Setup5-235-10 Onboard IndicatorsJLAN1/JLAN2 LEDsEach Ethernet port has two LEDs. One LED indicates activity while the

5-24SUPERWORKSTATION 7045A-T/7045A-8 User's Manual5-11 Parallel Port, Floppy and Hard Drive ConnectionsNote the following when connecting the fl

Chapter 5: Advanced Serverboard Setup5-25Floppy ConnectorThe fl oppy connector is located near the IDE connectors. See the table below for pin defi nit

viTable of ContentsPrefaceAbout This Manual ... ii

5-26SUPERWORKSTATION 7045A-T/7045A-8 User's ManualIDE Drive ConnectorsPin Defi nitions (IDE#1/IDE#2)Pin# Defi nition Pin #

Chapter 5: Advanced Serverboard Setup5-27Ultra320 SCSI Drive ConnectorPin Defi nitions (JA1/JA2)Pin# Defi nition Pin # Defi nit

5-28SUPERWORKSTATION 7045A-T/7045A-8 User's ManualNotes

Chapter 6: Advanced Chassis Setup6-1Chapter 6 Advanced Chassis SetupThis chapter covers the steps required to install components and perform si

6-2SUPERWORKSTATION 7045A-T/7045A-8 User's Manual6 x SATA Drive Bays (7045A-T) or8 x SCSI Drive Bays (7045A-8)Figure 6-1. Chassis Front ViewSyst

Chapter 6: Advanced Chassis Setup6-36-2 Front Control PanelThe front control panel must be connected to the JF1 connector on the serverboard to provid

6-4SUPERWORKSTATION 7045A-T/7045A-8 User's Manual6-3 System FansFour 80-mm chassis cooling fans (located in the center of the chassis) provide co

Chapter 6: Advanced Chassis Setup6-5Figure 6-4. Removing the Air ShroudFigure 6-3. Removing a Chassis Fan

6-6SUPERWORKSTATION 7045A-T/7045A-8 User's Manual1. Installing/removing hot-swap SATA/SCSI drives The SATA/SCSI drive carriers are all easil

Chapter 6: Advanced Chassis Setup6-7Figure 6-6. Mounting a SATA/SCSI Drive in a Carrier!Important! Regardless of how many SATA/SCSI hard drives are

Chapter 5: Advanced Serverboard Setup5-1 Handling the Serverboard ... 5-

6-8SUPERWORKSTATION 7045A-T/7045A-8 User's ManualFigure 6-7. SCSI BackplaneJumper Settings JP19: Buzzer Enable, Closed (On) Enabled (defau

Chapter 6: Advanced Chassis Setup6-9Installing Components in the 5.25" Drive Bays1. Drive bay confi guration The 7045A-T/7045A-8 has two 5.25

6-10SUPERWORKSTATION 7045A-T/7045A-8 User's Manual6-5 Power SupplyThe SuperWorkstation 7045A-T/7045A-8 has a single 645 watt power supply. This

Chapter 7: BIOS7-1Chapter 7 BIOS 7-1 IntroductionThis chapter describes the Phoenix BIOS™ Setup utility for the X7DAE/X7DA8. The Phoenix ROM B

7-2SUPERWORKSTATION 7045A-T/7045A-8 User's Manual7-2 Running SetupNote: Default settings are in bold text unless otherwise noted.The BIOS setup o

Chapter 7: BIOS7-3Main BIOS Setup MenuMain Setup FeaturesSystem TimeTo set the system date and time, key in the correct information in the appropriate

7-4SUPERWORKSTATION 7045A-T/7045A-8 User's ManualIDE Channel 0 Master/Slave, IDE Secondary Master/SlaveThese settings allow the user to set the

Chapter 7: BIOS7-5CHS FormatThe following items will be displayed by the BIOS:Type: This item displays the type of IDE or SATA drive.Cylinders: This i

7-6SUPERWORKSTATION 7045A-T/7045A-8 User's ManualParallel ATAThis setting allows the user to enable or disable the function of Parallel ATA. Th

Chapter 7: BIOS7-7System MemoryThis display informs you how much system memory is recognized as being present in the system.Extended MemoryThis displa

viiiAC'97 Audio ... 5-18CD Connectors ...

7-8SUPERWORKSTATION 7045A-T/7045A-8 User's ManualBoot FeaturesQuick Boot ModeIf enabled, this feature will speed up the POST (Power On Self Test

Chapter 7: BIOS7-9Memory CacheCache System BIOS AreaThis setting allows you to designate a reserve area in the system memory to be used as a System B

7-10SUPERWORKSTATION 7045A-T/7045A-8 User's ManualSelect "Uncached" to disable this function. Select "Write Through" to allow

Chapter 7: BIOS7-11Enable MasterThis setting allows you to enable the selected device as the PCI bus master. The options are Enabled and Disabled.Lat

7-12SUPERWORKSTATION 7045A-T/7045A-8 User's ManualBranch 1 Rank SparingSelect enable to enable the sparing feature for Branch 1 of memory bus. T

Chapter 7: BIOS7-13Advanced Processor OptionsAccess the submenu to make changes to the following settings. CPU SpeedThis is a display that indicates

7-14SUPERWORKSTATION 7045A-T/7045A-8 User's ManualIntel <R> Virtualization Technology (Available when supported by the CPU.)Select Enabled

Chapter 7: BIOS7-15 Base I/O AddressThis setting allows you to select the base I/O address for serial port B. The options are 3F8, 2F8, 3E8 and 2E8.I

7-16SUPERWORKSTATION 7045A-T/7045A-8 User's ManualDMI Event LoggingAccess the submenu to make changes to the following settings. Event Log Valid

Chapter 7: BIOS7-17Console Redirection Access the submenu to make changes to the following settings. COM Port AddressThis item allows you to specify

Table of ContentsixChapter 7: BIOS 7-1 Introduction ...

7-18SUPERWORKSTATION 7045A-T/7045A-8 User's ManualHardware Monitor LogicCPU Temperature ThresholdThis option allows the user to set a CPU temper

Chapter 7: BIOS7-19IPMI (Available only when an IPMI card is installed.) IPMI Specifi cation Version: This item displays the current IPMI Ver

7-20SUPERWORKSTATION 7045A-T/7045A-8 User's ManualOS Boot Watch DogSet to Enabled to enable OS Boot Watch Dog. The options are Enabled and Disabl

Chapter 7: BIOS7-21Realtime Sensor DataThis feature display information from motherboard sensors, such as temperatures, fan speeds and voltages of va

7-22SUPERWORKSTATION 7045A-T/7045A-8 User's Manual7-5 Security SettingsChoose Security from the Phoenix BIOS Setup Utility main menu with the arr

Chapter 7: BIOS7-23Password on BootThis setting allows you to require a password to be entered when the system boots up. The options are Enabled (pas

7-24SUPERWORKSTATION 7045A-T/7045A-8 User's Manual7-7 ExitChoose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys. You sho

A-1Appendix A: BIOS POST Messages Appendix A BIOS POST MessagesDuring the Power-On Self-Test (POST), the BIOS will check for problems.

A-2SUPERWORKSTATION 7045A-T/7045A-8 User's ManualSystem CMOS checksum bad - Default confi guration usedSystem CMOS has been corrupted or modifi ed

A-3Appendix A: BIOS POST MessagesSystem cache error - Cache disabledRAM cache failed and BIOS disabled the cache. On older boards, check the cache jum